By | 26.06.2019
Main->Hook->7 Bathtub Plumbing Installation Drain Diagrams

7 Bathtub Plumbing Installation Drain Diagrams

How to Install a Bathtub Drain

If you have any misgivings about doing it, hire a plumber who has the experience to install it and the license to hook up the fixtures. The first step in installing a tub is to set in place a ledger board that supports the edges of the tub that contact the walls of the tub enclosure. Push the tub into the enclosure and mark the top of the flange on the wall studs with a pencil. Measure and mark the location for the top of the ledger, usually about 1 inch below the first mark. Use coarse drywall screws to fasten the ledger board horizontally and level across the back wall of the alcove. Fasten shorter ledger boards to the ends of the enclosure, level with the board you install on the back wall.

Bathtub Plumbing Installation Drain Diagrams

Fit the gasket over the portion of the drain that protrudes out of the bottom of the tub, followed immediately by the drain ell. Hold the drain ell in place with one hand.

Insert the handles of your pliers into the section of the drain inside the tub. Open the handles as wide as possible to create a handle and tighten the drain clockwise.

Wipe away the excess sealant. Wedge another gasket between the overflow ell and the overflow opening on the tub. Instruct your friend to place the overflow hold down plate into position and hand-fasten it with the provided screws. Sit the tub upright before tightening the screws all the way down. Slip the compression nuts over the tail pieces of both the drain and overflow ells with the threads facing away from the tub.

Tub drain hook up

Push the cone washer onto the tailpipes so that the tapered side will fit into the drain tee of your rough-in plumbing, 1 to 2 inches from the end of the tailpiece. Carefully set the tub into position so that the both tail pieces slide effortlessly into the drain tee -- it may be helpful to recruit a third person to watch through the plumbing access as you make this connection.

This article shows how to install a waste-and-overflow tube on your bathtub, Every tub is built a little different, and the drain can be located in.

Tighten the compression nuts coming from both the drain and overflow by hand from the access until you cannot turn them anymore. Give them another half turn with the slip-joint pliers. Install the stopper and overflow lift rod according to package directions. Kristi Waterworth started her writing career in as a journalist for a local newspaper.

Sinceshe's written on a wide range of personal finance topics. Skip to main content.

Tip It is vital that your drain and rough-in line up exactly. If in doubt, pull the tub and realign without the tailpieces installed. It may take several attempts to get this right. A bathtub drain flange is the finished drain part that's visible in the tub. Some manufacturers refer to the drain flange as a "drain body" or "drain basket".

Drain flanges come in many different finishes and have a variety of stopper options for filling the tub. Replacing the flange is a relatively simple project, but if you haven't done it before you may have a tough time knowing where to begin. Before you dive in, it's important to familiarize yourself with a tub drain system. As the diagram at right above shows, the flange is held in place with a threaded connection to the drain elbow aka drain shoe.

Between the underside of the flange and the tub surface, there's a good amount of plumbers putty that seals the inside of the drain. A rubber gasket underneath the tub seals the drain elbow to the tub. That drain elbow connects to a length of pipe that then connects to the waste and overflow pipe.

The most difficult part of installing the tub itself is hooking up the bathtub drain to the rough plumbing. If there is no access to the drain from behind or below, and. The first step in installing a tub is to set in place a ledger board that supports the edges of It's easier to install the drain and overflow pipes on the tub before it's. A tub drain with a built-in stopper has distinct advantages over other types of drains. They are more durable and easier to maintain than pop-up.

Before beginning please note: There are many variables to consider when it comes to your home's plumbing - this guide is intended to provide a basic understanding, and may not cover all circumstances. Before attempting any DIY plumbing project in your home, know the access points to your plumbing.

Many bathtubs will have an access panel behind the tub, or you may be able to access the plumbing through a crawl space in or under the home. Keep in mind when attempting to complete a plumbing project yourself that it's easy to "open a can of worms" - you need to be prepared if your simple project suddenly gets out of hand.

Both the Drain Key and the Smart Dumbell essentially work the same; you insert them into the drain and turn counterclockwise to release the old tub drain. However, they are slightly different. For your convenience, we offer a complete tutorial for using these drain tools. Step 1 First, remove the stopper. There are several types of drain stopper, all of which can be removed very easily.

How to Install a Tub Drain. Whether you're fixing a faulty drain or upgrading your hardware, installing a new drain is a fairly straightforward job. View Diagrams of Bathtub Plumbing Installation and Bathtub Drain pry up the bucket with the attached rod, you may be able to clean it up. Over time, bathtub drains -- like all drains -- tend to become broken, cracked or worn out. When that happens, the drain needs to be replaced. Regardless of the .

Following the instructions for the tool, turn counterclockwise. Step 3 Keep turning drain counterclockwise until the old drain is released - it shouldn't take too many turns before the drain comes right out. After a few minutes, the putty should be soft enough to try turning again.

Step 4 Clean drain area, making sure to remove all old putty residue.

Allow to dry before beginning installation of the new drain flange. Step 5 Underneath the tub will be a rubber gasket that creates a seal for the drain elbow.

How to Install a Bathtub Drain and Overflow
Next related articles:
  • Dating fish website
  • 0 comments

    Leave a Reply

    Your email will not be published. Required fields are marked *